Kit for the hinged door hood. Hood assembly instructions below. 

Please choose the right size for your printer!

This tape should be installed on top of your LCD screen to help protect your printer from resin spills as well as hold your LCD screen in place. It will prevent any leaked resin from dripping underneath your screen and potentially damaging your printer. It will also hold your screen in place if you have to lay your printer down to perform maintenance, etc.

The 15.6" screen tape is cut and sized to fit EPAX X156 with 15.6" 4K color screen.

The 13.3" screen tape is cut and sized to fit EPAX X133 with 13.3" 4K and 6K mono screen.

This is the screen tape ONLY. Replacement LCD screens must be purchased separately.

Our resin vats are made entirely of durable, machine-anodized aluminum. This vat will fit EPAX X133 3D printers. Each vat comes with a sheet of nFEP film already installed, so it will arrive ready to use. 

Features

• Aluminum build means the tank will not be harmed by resin or curing process
• Equipped with a rubber seal to ensure that vat is water-tight to avoid resin leaks
• Groove in the front-right corner allows for draining residual resin simple and quick
• Hash-marks indicate resin levels for the vat.
• Max volume of 2400mL without build platform and 1700mL with build platform.

Our resin vats are made entirely of durable, machine-anodized aluminum. This vat will fit EPAX X156 3D printers. Each vat comes with a sheet of nFEP film already installed, so it will arrive ready to use. 

Features

• Aluminum build means the tank will not be harmed by resin or curing process
• Equipped with a rubber seal to ensure that vat is water-tight to avoid resin leaks
• Groove in the front-right corner allows for draining residual resin simple and quick
• Hash-marks indicate resin levels for the vat.
• Max volume of 3300mL without build platform and 2300mL with build platform.

Choose the right build platform for your model.  There are two molded build platform available.  One for E10 printer and one for E6 printer. 

This low-cost molded build plate has metal sheet attached to bottom and comes with all of the parts necessary to install it quickly and easily into your printer. All that is necessary is to calibrate the plate to your machine. It is calibrated in the same way as any our build plate.

Note that you must level this build plate for your printer.  The build plate is dedicated to one of your printers and cannot be used with other printers without releveling to that printer.  So please mark the build plate to the printer name.

E10 Molded Build Platform: XY size:  232mm x 141.7mm

E6 Molded Build Platform: XY size:  128mm x 78mm

E10 vat is molded with non-corrosive plastic and fits EPAX E10 series 3D printers.  It can support an 8.9" screen or 10.1" screen on E10.  Each vat comes with a sheet of nFEP film already installed, so it will arrive ready to use. 

• E10 molded vat only fits the E10 printer
• E6 molded vat is for the E6 printer

Features

• The molded tank allows for cheap replacements and extras for switching out resin on the fly
• Fiberglass reinforced plastic sports increased durability and resistance to corrosion and resin.
• It is equipped with a rubber seal to ensure that the vat is water-tight to help avoid resin leaks.
• E10 Vat Max Volume 1500mL without build platform and 700mL with the build platform
• E6 Vat Max Volume 300mL without build platform and 200mL with the build platform

Build platform for the EPAX X156 3D printer. It is made from soft aluminum with a sanded surface for the best adhesion and print removal, and it is constructed to be stable for minimal re-leveling.

Dimensions: 220mm x 370mm

Angled X156 Build Platform Benefits

Using this build platform will minimize resin accumulation on the stop of the plate, allowing it to more readily drip back into the vat during printing. This makes clean-up and print removal faster, easier, and less messy overall so that you can spend more time printing.

This build plate comes with all of the parts necessary to install it quickly and easily into your printer. All that is necessary is to calibrate the plate to your machine. It is calibrated in the same way as all other build plates of all printers. See the video below as a reference:

Build platform for the EPAX X133 3D printer. It is made from soft aluminum with a sanded surface for the best adhesion and print removal, and it is constructed to be stable for minimal re-leveling.

Angled X133 Build Platform Benefits

Using this build platform will minimize resin accumulation on the stop of the plate, allowing it to more readily drip back into the vat during printing. This makes clean-up and print removal faster, easier, and less messy overall so that you can spend more time printing.

This build plate comes with all of the parts necessary to install it quickly and easily into your printer. All that is necessary is to calibrate the plate to your machine. It is calibrated in the same way as all other build plates of all printers. See the video below as a reference:

Please choose the right size for your printer!

This tape should be installed on top of your LCD screen to help protect your printer from resin spills as well as hold your LCD screen in place. It will prevent any leaked resin from dripping underneath your screen and potentially damaging your printer. It will also hold your screen in place if you have to lay your printer down to perform maintenance, etc.

The 10.1" screen tape is cut and sized to fit EPAX X10 with 10.1" 2K color screen printers. It is ready to install.

The 8.9" screen tape is cut and sized to fit EPAX X10 with 8.9" 4K mono screen printers and EPAX E10 printers. It is ready to install.

This is the screen tape ONLY. Replacement LCD screens must be purchased separately.

• Fit for EPAX E10/X10 printer
• Excellent quality: resistant to high temperatures (260 ° C), Chemically resistant, Ultimate non-stick surface, UV stable.
• Perfectly smooth, smoother than FEP films.  Great air permeability leads to less vacuum suction force. As such, you will have fewer failed prints than using FEP films.
• Shipped in protective packaging.
• Each tube contains one (1) film
• 0.125mm thickness 

Our films are a special blend of Teflon material.  Used in DLP and SLA machines as well (different size) due to high requirements by those printers.

How to Replace nFep Film

Films are Made in Japan, Cut and Packed in China

Our nFEP films are a special blend of Teflon material, superior to standard FEP films and ideal for large-format printers when you will truly be able to recognize the benefits.

Dimension: 435mm x 290mm  (17.1" x 11.4")

This package of film includes ONE (1) piece of nFEP film sized for the EPAX X156 15.6" LCD 3D printer with 0.125mm thickness.

• nFEP is excellent quality: resistant to high temperatures (up to 260° C), chemically resistant, UV stable and providing the ultimate non-stick surface
• It is perfectly smooth - smoother than FEP films - with optimal air permeability, which leads to less vacuum suction force for fewer failed prints due to layers sticking to the film
• Each package is shipped in thoughtful protective packaging.

How to Replace nFep Film

This is an alternate, optional build platform for the EPAX X10 3D printer. It is made from soft aluminum with a sanded surface for the best adhesion and print removal, and it is constructed to be stable for minimal re-leveling.

This build platform is only compatible with X10 printers, it is not compatible with E10 printers.  E10 requires a different top bracket.

Angled X10 Build Platform Benefits

Using this build platform will minimize resin accumulation on the top of the plate, allowing it to more readily drip back into the vat during printing. This makes clean-up and print removal faster, easier, and less messy overall so that you can spend more time printing.

This build plate comes with all of the parts necessary to install it quickly and easily into your printer. All that is necessary is to calibrate the plate to your machine. It is calibrated in the same way as the standard flat build plate.

This is a replacement Z-axis motor and lead screw for EPAX LCD resin printers. The X156 motor does not come with a lead screw.

Our resin vats are made entirely of durable, machine-anodized aluminum. This vat will fit EPAX X10 3D printers (except the latest X10-8KW, which uses a wider vat). Each vat comes with a sheet of nFEP film already installed, so it will arrive ready to use. 

Features

• The completely metal resin tank will not be harmed by resin nor the curing process. 
• It is equipped with a rubber seal to ensure that the vat is water-tight to help avoid resin leaks.
• The groove in the front right corner makes draining residual resin easy and fast.
• Hash-marks on the back edge of the vat indicate resin levels.
• Max Volume of 1250mL without build platform and 900mL with build platform.

This is a replacement power supply for your printer. Please choose the correct model first.

Power Supplies for the following printers: 

24V Power Supply --> E10 / X10 / X1-4K / X1-4KS / E6 / X1-K

12V Power Supply --> X1-Classic / X1-N 

X156 and X133

If you order from another country and require a different plug style, you can replace the cord. The cord detaches from the power brick.

X1-K and E6 share the same mainboard but slightly different firmware, because the slightly difference on the 6" mono screen size.  

You will need to check which version X1 you have. X1-Classic X1-N, X1-K, and E6 will all use this mainboard but will use different firmware. The X1 mainboard uses an SX04 interface to the LCD screen and its firmware uses CTB file format to print instead of the CBDDLP file format that the older X1-Classic mainboards used. Because of where the screen cable connector is located, customers replacing the X1-classic mainboards will need to remove the right angle adapter from the end of their screen cable before connecting to the mainboard. FAILURE TO DO SO WILL SHORT OUT THE MAINBOARD AND THE SCREEN.

Please contact support@epax3d.com if you have any questions.

Our Non-FEP (nFEP) films are a special blend of Teflon material, superior to standard FEP films and ideal for large-format printers when you will truly be able to recognize the benefits.

Dimension: 380mm x 260mm  (15" x 10.2")

This package of film includes ONE (1) piece of nFEP film sized for the EPAX X133 13.3" LCD 3D printer with 0.125mm thickness.

• nFEP is excellent quality: resistant to high temperatures (up to 260° C), chemically resistant, UV stable and providing the ultimate non-stick surface
• It is perfectly smooth - smoother than FEP films - with optimal air permeability, which leads to less vacuum suction force for fewer failed prints due to layers sticking to the film
• Each package is shipped in thoughtful protective packaging.

How to Replace nFep Film

Films are Made in Japan, Cut and Packed in China

Please choose the right size for your printer!.

This tape should be installed on top of your LCD screen to help protect your printer from resin spills as well as hold your LCD screen in place. It will prevent any leaked resin from dripping underneath your screen and potentially damaging your printer. It will also hold your screen in place if you have to lay your printer down to perform maintenance, etc.

The 5.5" variant is cut and sized to fit EPAX X1 and X1-DJ printers. It is ready to install.

The 6" variant is cut and sized to fit EPAX X1K 6" printer and E6 printer. It is ready to install.

This is the screen tape ONLY. Replacement LCD screens must be purchased separately.

One way to apply tape to 5.5" LCD screen:

1. Wear UV protective glasses.  Download the 5.5" screen-edge.cbddlp file which will show you the edge of displayable screen. You can find the frame file here.
2. Remove both vat and build platform. "Print" the above cbddlp file and observe the light on each side of the display area.
3. Apply the pre-cut tape to the light frame so that the light frame is still seen.  On each of the 4 sides there is about 1mm room of extra space so you don't necessarily need to apply the tape precisely.  The tape is 2mm larger than the display area on all sides.
4. Press the tape so that it is secure and even. Try to avoid creases.
5. Perform an Auto-Home without the vat in place and then with the vat.

Another way to apply tape:

1. Wear UV protective glasses
2. Remove both vat and build platform. Select "Calibrate" on touchscreen.  Use a thick cardboard to cover the displayed rectangle.
3. Apply the pre-cut tape to the lighted area along the lighted edge.  
4. Press the tape so that it is secure and even. Try to avoid creases.
5. Perform an Auto-Home without the vat in place and then with the vat.

See the video below for installation:

As pictured. This is the touchscreen ONLY. The ribbon cable is not included. 

The 3.5" color TFT touchscreen is compatible with EPAX printer models including X1 series, E6, E10 series and X10 series. It comes covered with a protective film and is ready to install.

Our soft aluminum EPAX X1 build plates allow for both optimal bottom layer adhesion as well as print removal. They have a gently sanded surface and are constructed to be stable, secure and seldom require re-leveling.

This build platform has all the parts/screws necessary to install it right away.  

If you choose a "Slightly Scratched" build platform you may see some signs of use when your platform arrives. They were likely scratched during factory testing. These scratches will not affect print adhesion or printing in any way. Scratches are actually known to improve adhesion and platforms inevitably become scratches over time.

Works with all EPAX X1 series printers of 5.5" and 6" screens.  For X1-4KS printer, which uses 6.6" screen, please choose its model.

NOTE: Before using your new build platform, be sure to calibrate it for your EPAX 3D printer. 

See the video below for how to level or re-level your build plate:

Made entirely of durable anodized aluminum and with a sheet of nFEP film already installed, this EPAX X1 resin vat will arrive ready to use. 

Features

• The completely metal resin tank will not be harmed by resin nor the curing process. 
• It is equipped with a rubber seal to ensure that the vat is water-tight.
• The groove in the front right corner makes draining unused resin easy and fast.
• Hash-marks on the back edge of the vat indicate resin levels.
• Max Volume is 450mL without build platform and 300mL with build platform.

• This 3-pack of films are fit for all EPAX X1 series 3D Printers, including X1-Classic, X1-DJ, X1-N, X1-K and also E6 printers, because they all share the same size of vat.
• Size: LxW 200x140mm/7.8x5.5 inch
• New 0.125mm thickness, compared to previous 0.1mm thickness
• Our nFEP films are excellent quality: resistant to high temperatures (up to 220° C), chemical resistant, UV stable and provide the ultimate non-stick surface for 3D resin printing.
• nFEP is perfectly smooth - smoother than FEP film - with great air permeability, which leads to less vacuum suction force. So you will have fewer failed prints compared to standard FEP film.
• All of our films are shipped in thoughtful, protective packaging to ensure they arrive to you in pristine condition.
• Each pack contains three (3) films

How to Replace nFep Film

Films are Made in Japan, Cut and Packed in China