• This 3-pack of films are fit for all EPAX X1 series 3D Printers, including X1-Classic, X1-DJ, X1-N, X1-K and also E6 printers, because they all share the same size of vat.
• Size: LxW 200x140mm/7.8x5.5 inch
• New 0.125mm thickness, compared to previous 0.1mm thickness
• Our nFEP films are excellent quality: resistant to high temperatures (up to 220° C), chemical resistant, UV stable and provide the ultimate non-stick surface for 3D resin printing.
• nFEP is perfectly smooth - smoother than FEP film - with great air permeability, which leads to less vacuum suction force. So you will have fewer failed prints compared to standard FEP film.
• All of our films are shipped in thoughtful, protective packaging to ensure they arrive to you in pristine condition.
• Each pack contains three (3) films

 

How to Replace nFep Film

 

Films are Made in Japan, Cut and Packed in China

 

Please choose the right size for your printer!.

This tape should be installed on top of your LCD screen to help protect your printer from resin spills as well as hold your LCD screen in place. It will prevent any leaked resin from dripping underneath your screen and potentially damaging your printer. It will also hold your screen in place if you have to lay your printer down to perform maintenance, etc.

The 5.5" variant is cut and sized to fit EPAX X1 and X1-DJ printers. It is ready to install.

The 6" variant is cut and sized to fit EPAX X1K 6" printer and E6 printer. It is ready to install.

This is the screen tape ONLY. Replacement LCD screens must be purchased separately.

One way to apply tape to 5.5" LCD screen:

1. Wear UV protective glasses.  Download the 5.5" screen-edge.cbddlp file which will show you the edge of displayable screen. You can find the frame file here.
2. Remove both vat and build platform. "Print" the above cbddlp file and observe the light on each side of the display area.
3. Apply the pre-cut tape to the light frame so that the light frame is still seen.  On each of the 4 sides there is about 1mm room of extra space so you don't necessarily need to apply the tape precisely.  The tape is 2mm larger than the display area on all sides.
4. Press the tape so that it is secure and even. Try to avoid creases.
5. Perform an Auto-Home without the vat in place and then with the vat.

Another way to apply tape:

1. Wear UV protective glasses
2. Remove both vat and build platform. Select "Calibrate" on touchscreen.  Use a thick cardboard to cover the displayed rectangle.
3. Apply the pre-cut tape to the lighted area along the lighted edge.  
4. Press the tape so that it is secure and even. Try to avoid creases.
5. Perform an Auto-Home without the vat in place and then with the vat.

 

See the video below for installation:

 

Includes:

• LCD screen
• Screen Cable
• 1x precut tape 

 

Use the guide below to choose the correct screen for your printer model

E10-5K/X10-5K: 10.1" 5K mono screen.

E10-8K/X10-8K: 10.1" 8K mono screen.

E10-14KW/X10-14KW: 10.1" 14K mono screen

X1-4KS: 6.6" 4K mono screen.

X1K/E6: 6" 2K mono screen.

X1-4K: 5.5" 4K mono screen.

X10-4K/E10: 8.9" 4K mono screen. 

*There are some open box brand new screens due to upgrading E10 to E10-5K printers. Open boxed screens have signs of installation but never printed.

X10: 10.1" 2K color screen.

X1-Classic/X1-N/X1-DJ/X1-N-DJ: 5.5" 2K color screen with SX03.  

X1-Classic/X1-N/X1-DJ/X1-N-DJ: 5.5" 2K color screen with SX04.

*If you are unsure, please email to support@epax3d.com to help you find out which interface yours is.

X133: 13.3" 6K mono screen.

X133: 13.3" 7K mono screen.

NOTE TO EXISTING X133 CUSTOMERS: Our company is currently transitioning the X133 printers to a 7K mono-screen. Replacement 7K screens will be offered at the same price as the 4k LCD screens.  Matching 7K mainboard is free with 13.3" 6K screen purchase. To get the free 7K mainboard with 7K screen purchase, please email us at support@epax3d.com for arrangement. 

 

X156: 15.6" 4K color screen. 

X156: 16" 8K mono screen, only purchase this if you already upgraded your X156 to 16" 8K before. 

Replacing your screen always involved re-leveling your build plate.

ALWAYS make sure your vat is free from any debris and that the build plate has nothing on it before starting a new print job.  Monochrome screens are more expensive due to being produced in smaller volumes only for 3D printing.

Disclaimer: Using this screen with non EPAX 3D printers is NOT supported.

 

You can reference below general guide for screen replacement:

 

https://epax3d.com/blogs/news/quick-guide-for-upgrade-from-x10-10-1-2k-color-to-x10-8-9-4k-mono

Epax screen protectors are similar to a cell phone's anti-scratch screen protector but are tailored to work with Epax Printers. Epax screen protectors are a great way to protect your LCD screen from potential damage that may occur if there is a resin spill.

Please make sure you choose the right screen size for your model.

There are protective films on both sides of the screen protector.  When you apply the protector, you need to peel off the film labeled "back" and then apply using the plastic spatula to the screen's surface carefully, starting from one corner. Having some bubbles may be unavoidable but they should not affect your prints.

This is a light upgrade/mod kit for the EPAX X1 series only (X1-Classic, X1-N, X1-K). This parallel matrix UV light kit has all the parts and screws necessary to change your existing, standard X1 light source to this newer light source that adds more dimensional accuracy and can capture the finer details of your prints- great for dental and jewelry applications.

Made entirely of durable anodized aluminum and with a sheet of nFEP film already installed, this EPAX X1 resin vat will arrive ready to use. 

Features

• The completely metal resin tank will not be harmed by resin nor the curing process. 
• It is equipped with a rubber seal to ensure that the vat is water-tight.
• The groove in the front right corner makes draining unused resin easy and fast.
• Hash-marks on the back edge of the vat indicate resin levels.
• Max Volume is 450mL without build platform and 300mL with build platform.

Our soft aluminum EPAX X1 build plates allow for both optimal bottom layer adhesion as well as print removal. They have a gently sanded surface and are constructed to be stable, secure and seldom require re-leveling.

This build platform has all the parts/screws necessary to install it right away.  

If you choose a "Slightly Scratched" build platform you may see some signs of use when your platform arrives. They were likely scratched during factory testing. These scratches will not affect print adhesion or printing in any way. Scratches are actually known to improve adhesion and platforms inevitably become scratches over time.

Works with all EPAX X1 series printers of 5.5" and 6" screens.  For X1-4KS printer, which uses 6.6" screen, please choose its model.

NOTE: Before using your new build platform, be sure to calibrate it for your EPAX 3D printer. 

See the video below for how to level or re-level your build plate:

This is a replacement Z-axis motor and lead screw for EPAX LCD resin printers. The X156 motor does not come with a lead screw.

These are the replacement resin vat screws for Epax 3D printers. These screws hold the vat in place during the printing process. Please make sure you select the correct screws for the machine you have.

• Each pack contains 2 resin tank screws 

As pictured. This is the touchscreen ONLY. The ribbon cable is not included. 

The 3.5" color TFT touchscreen is compatible with EPAX printer models including X1 series, E6, E10 series and X10 series. It comes covered with a protective film and is ready to install.

This is a replacement power supply for your printer. Please choose the correct model first.

Power Supplies for the following printers: 

24V Power Supply --> E10 / X10 / X1-4K / X1-4KS / E6 / X1-K

12V Power Supply --> X1-Classic / X1-N 

X156 and X133

If you order from another country and require a different plug style, you can replace the cord. The cord detaches from the power brick.

X1-K and E6 share the same mainboard but slightly different firmware, because the slightly difference on the 6" mono screen size.  

You will need to check which version X1 you have. X1-Classic X1-N, X1-K, and E6 will all use this mainboard but will use different firmware. The X1 mainboard uses an SX04 interface to the LCD screen and its firmware uses CTB file format to print instead of the CBDDLP file format that the older X1-Classic mainboards used. Because of where the screen cable connector is located, customers replacing the X1-classic mainboards will need to remove the right angle adapter from the end of their screen cable before connecting to the mainboard. FAILURE TO DO SO WILL SHORT OUT THE MAINBOARD AND THE SCREEN.

Please contact support@epax3d.com if you have any questions.

The Slotted Optical Switch is used to determine the home position of all Epax3D machines. If you are having issues with the build plate rising when you press the home button, your build plate thinking its at the home position when it's not, the red light on the optical switch flickering or not coming on at all, then you may need to replace the Optical Switch.

This is the replacement build plate knob for Epax 3D printers. Please make sure you select the correct knob for the machine you have.

 

• 0.125mm thickness
• Our nFEP films are excellent quality: resistant to high temperatures (up to 220° C), chemical resistant, UV stable and provide the ultimate non-stick surface for 3D resin printing.
• nFEP is perfectly smooth - smoother than FEP film - with great air permeability, which leads to less vacuum suction force. So you will have fewer failed prints compared to standard FEP film.
• All of our films are shipped in thoughtful, protective packaging to ensure they arrive to you in pristine condition.
• Each tube contains 1 film

 

How to Replace nFep Film

Films are Made in Japan, Cut and Packed in China

This magnetic build plate is compatible with X1-4KS 6.6" printers. It is attached to the existing build platform of X1-4KS printers using an adhesive magnetic pad.  Does not come with the build platform itself. Not recommended for dental use.

You can choose the magnetic pad+steel plate or the steel plate by itself.

Two options to choose from:

1, Magnetic pad and Steel Plate

2, Steel Plate Only

Steps to apply:

1, Clean your existing Metal Build Platform well.  Make sure no IPA is left on the existing build surface since IPA can dissolve the glue of the magnetic pad.

2, Glue magnetic pad to the existing build platform.  The pad comes with glue pre-applied.

3, Put the steel plate on.

4, Re-level the new whole Build Platform similar to before.

Size: 5.75" x 3.625" (146mm x 92mm) 

Caution:

You can use IPA to clean the steel plate and magnetic pad surface.  But not to soak the magnetic pad in IPA.  Doing that will lead to the separation of the pad from the build platform since IPA can dissolve the glue. 

 

This magnetic build plate comes ready to install on your build platform quickly. After applying the magnetic pad and steel plate to your existing build platform, you must recalibrate your build platform because of the increased height of the build surface. Failure to relevel/recalibrate your build platform could result in damage to other parts such as the LCD screen. 

See the video below for how to level or re-level your build plate:

• X10 size fits for all EPAX X10/E10 printers
• X1-4KS size fits for all EPAX X1 series printers.
• Excellent slippery surface: enabling faster printing with less release force and less lifting distance.
• Shipped in protective tube.  
• Each pack contains one (1) film
• 0.3mm thickness 

These films are composite films with a coating on one side to ensure great slippery.  Used in LCD, DLP and SLA machines where fast printing is more important than quality/durable parts.

Note:  The sides are directional.  Do not put it upside down.  See instructions on the film.  There is a protective film on the actual eSLIP film.  The protective film needs to be removed.

Difference between nFEP film and eSLIP/ACF film:

nFEP film is more elastic.  As such, it is less likely to be damaged by residues in vat.  It is recommended for all resin 3D printers, especially jewelry/dental applications where details and quality are more important.  nFEP film has great air permeability, which leads to less vacuum suction force.

eSLIP/ACF film is more rigid and slippery.  As such it needs a smaller lifting distance and prints can run faster.  Printers with eSLIP film can have an overall 40% speed gain due to lower lifting distance needed.  You also need to increase your bottom exposure time and normal exposure time by 20% because the film has 20% less light through rate.  It is recommended for all resin 3D printers where faster printing is more important than outstanding details.  However, if you leave residues in vat, the film is a bit easier to get damaged than nFEP film.  The coating, and the 0.3mm thickness, lead to a bit loss of light accuracy.  Fast printing resins, because they flow like water, are also not able to make strong and tough parts.  Parts tend to be more brittle.  As such, we don't offer fast printing resins.  You can use the film with normal resins and it can still speed up somewhat due to lower lifting distance alone.

The USB extension cable connects from the mainboard inside of the printer to the outer case of the machine.

The Ethernet extension cable connects from the mainboard inside of the printer to the outer case of the machine.