• Fit for EPAX E10/X10 printer
• Excellent quality: resistant to high temperatures (260 ° C), Chemically resistant, Ultimate non-stick surface, UV stable.
• Perfectly smooth, smoother than FEP films.  Great air permeability leads to less vacuum suction force. As such, you will have fewer failed prints than using FEP films.
• Shipped in protective packaging.
• Each tube contains one (1) film
• 0.125mm thickness 

Our films are a special blend of Teflon material.  Used in DLP and SLA machines as well (different size) due to high requirements by those printers.

How to Replace nFep Film

Films are Made in Japan, Cut and Packed in China

Please choose the right size for your printer!

This tape should be installed on top of your LCD screen to help protect your printer from resin spills as well as hold your LCD screen in place. It will prevent any leaked resin from dripping underneath your screen and potentially damaging your printer. It will also hold your screen in place if you have to lay your printer down to perform maintenance, etc.

The 10.1" screen tape is cut and sized to fit EPAX X10 with 10.1" 2K color screen printers. It is ready to install.

The 8.9" screen tape is cut and sized to fit EPAX X10 with 8.9" 4K mono screen printers and EPAX E10 printers. It is ready to install.

This is the screen tape ONLY. Replacement LCD screens must be purchased separately.

Please choose the right kit for your printer.  E10 and X10 use different brackets.

The EPAX X10/E10-8K 10.1 inch upgrade kits are made for all E10 and X10 machines with the parallel light source already installed. 

The 8K Upgrade Kit Includes: 

• 8K Mainboard
• 10.1" 8K Mono LCD Screen 
• 10.1'' Screen Tape 
• Screen Bracket

* You will need double-sided tape in order to install the screen to the bracket

FEATURES:

 

• 8k high resolution:  7680x 4320 with pixel size 28.5um

• 8K build volume of 218.88mm*123.12mm*250mm.
  

 

Installation instructions are available on our YouTube channel through the link below.

This parallel matrix UV light kit has all the parts and screws necessary to change your existing, standard X10 light source to this newer light source that adds more dimensional accuracy and can capture the finer details of your prints- great for dental and jewelry applications.

Includes:

• LCD screen
• Screen Cable
• 1x precut tape 

 

Use the guide below to choose the correct screen for your printer model

E10-5K/X10-5K: 10.1" 5K mono screen.

E10-8K/X10-8K: 10.1" 8K mono screen.

X1-4KS: 6.6" 4K mono screen.

X1K/E6: 6" 2K mono screen.

X1-4K: 5.5" 4K mono screen.

X10-4K/E10: 8.9" 4K mono screen. 

*There are some open box brand new screens due to upgrading E10 to E10-5K printers. Open boxed screens have signs of installation but never printed.

X10: 10.1" 2K color screen.

X1-Classic/X1-N/X1-DJ/X1-N-DJ: 5.5" 2K color screen with SX03.  

X1-Classic/X1-N/X1-DJ/X1-N-DJ: 5.5" 2K color screen with SX04.

*If you are unsure, please email to support@epax3d.com to help you find out which interface yours is.

X133: 13.3" 6K mono screen.

X133: 13.3" 7K mono screen.

NOTE TO EXISTING X133 CUSTOMERS: Our company is currently transitioning the X133 printers to a 7K mono-screen. Replacement 7K screens will be offered at the same price as the 4k LCD screens.  Matching 7K mainboard is free with 13.3" 6K screen purchase. To get the free 7K mainboard with 7K screen purchase, please email us at support@epax3d.com for arrangement. 

 

X156: 15.6" 4K color screen. 

Replacing your screen always involved re-leveling your build plate.

ALWAYS make sure your vat is free from any debris and that the build plate has nothing on it before starting a new print job.  Monochrome screens are more expensive due to being produced in smaller volumes only for 3D printing.

Disclaimer: Using this screen with non EPAX 3D printers is NOT supported.

 

You can reference below general guide for screen replacement:

https://epax3d.com/blogs/news/quick-guide-for-upgrade-from-x10-10-1-2k-color-to-x10-8-9-4k-mono

The EPAX E10-5K 10.1 inch upgrade kits are made for EPAX E10 4K 8.9-inch mono printers. 

The E10-5K upgrade kits include: 

• E10-5K Mainboard
• 10.1" Screen & Screen Bracket  (open box screen pulled out of brand new 5K printer)
• 10.1'' Screen Tape 

Only works with ChiTuBox Pro version slicers and Free Basic Version.   The mainboard and slicer both are supplied by ChiTuBox.  Other third-party slicers might need ChiTuBox's SDK in order to slice into files for this printer.

* You will need double-sided tape in order to install the screen to the bracket

FEATURES:

• 5k high resolution of 4920 *2800 

• 20% larger build surface 
• 221.4mm*129.6mm*250mm build volume 
• 565 pixels per inch

Installation instructions will be available at the time of shipment via this listing and our YouTube channel. 

 

 

X10-5K/E10-5K PRINTER SPECIFICATIONS

 

 

This is an alternate, optional build platform for the EPAX X10 3D printer. It is made from soft aluminum with a sanded surface for the best adhesion and print removal, and it is constructed to be stable for minimal re-leveling.

This build platform is only compatible with X10 printers, it is not compatible with E10 printers.  E10 requires a different top bracket.

Angled X10 Build Platform Benefits

Using this build platform will minimize resin accumulation on the top of the plate, allowing it to more readily drip back into the vat during printing. This makes clean-up and print removal faster, easier, and less messy overall so that you can spend more time printing.

 

This build plate comes with all of the parts necessary to install it quickly and easily into your printer. All that is necessary is to calibrate the plate to your machine. It is calibrated in the same way as the standard flat build plate.

Our resin vats are made entirely of durable, machine-anodized aluminum. This vat will fit EPAX X10 3D printers (except the latest X10-8KW, which uses a wider vat). Each vat comes with a sheet of nFEP film already installed, so it will arrive ready to use. 

Features

• The completely metal resin tank will not be harmed by resin nor the curing process. 
• It is equipped with a rubber seal to ensure that the vat is water-tight to help avoid resin leaks.
• The groove in the front right corner makes draining residual resin easy and fast.
• Hash-marks on the back edge of the vat indicate resin levels.
• Max Volume of 1250mL without build platform and 900mL with build platform.

 

This is a replacement Z-axis motor and lead screw for EPAX LCD resin printers. The X156 motor does not come with a lead screw.

 

This magnetic pad and steel plate are compatible with the X10 or E10 all-metal ANGLED build plate pictured below. It is attached to the existing build platform using an adhesive magnetic pad. This item does not come with the build platform itself. Not recommended for dental use.

 

This DOES NOT FIT the E10's standard Molded Platform or the rounded version 2 All-metal build plate pictured below.

 

 

 

You can choose the magnetic pad+steel plate or the steel plate by itself.

Two options to choose from:

1, Magnetic pad and Steel Plate

2, Steel Plate Only

Steps to apply:

1, Clean your existing Metal Build Platform well.  Make sure no IPA is left on the existing build surface since IPA can dissolve the glue of the magnetic pad.

2, Glue magnetic pad to the existing build platform.  The pad comes with glue pre-applied.

3, Put the steel plate on.

4, Re-level the new whole Build Platform similar to before.

Size: 9.12" x 5.625" (231mm x 143mm) 

Caution:

You can use IPA to clean the steel plate and magnetic pad surface.  But not to soak the magnetic pad in IPA.  Doing so will lead to the separation of the pad from the build platform since IPA can dissolve the glue. 

 

This magnetic build plate comes ready to install on your build platform quickly. After applying the magnetic pad and steel plate to your existing build platform, you must relevel your build platform because of the increased height of the build surface. Failure to relevel/recalibrate your build platform could result in damage to other parts such as the LCD screen. 

It is calibrated in the same way as the standard build platform.  See the video below as a reference:

 

As pictured. This is the touchscreen ONLY. The ribbon cable is not included. 

The 3.5" color TFT touchscreen is compatible with EPAX printer models including X1 series, E6, E10 series and X10 series. It comes covered with a protective film and is ready to install.

This is a replacement power supply for your printer. Please choose the correct model first.

Power Supplies for the following printers: 

24V Power Supply --> E10 / X10 / X1-4K / X1-4KS / E6 / X1-K

12V Power Supply --> X1-Classic / X1-N 

X156 and X133

If you order from another country and require a different plug style, you can replace the cord. The cord detaches from the power brick.

This is the replacement build plate knob for Epax 3D printers. Please make sure you select the correct knob for the machine you have.

The Slotted Optical Switch is used to determine the home position of all Epax3D machines. If you are having issues with the build plate rising when you press the home button, your build plate thinking its at the home position when it's not, the red light on the optical switch flickering or not coming on at all, then you may need to replace the Optical Switch.

These are the replacement resin vat screws for Epax 3D printers. These screws hold the vat in place during the printing process. Please make sure you select the correct screws for the machine you have.

• Each pack contains 2 resin tank screws 

The E10-4K/X10-4K mainboard is a replacement mainboard for EPAX E10 and X10 LCD printers with the 8.9" 4K mono screen.  This is the mainboard only and does not include any cables, connectors, or other components.

Please contact support@epax3d.com if you have any questions.

The USB extension cable connects from the mainboard inside of the printer to the outer case of the machine.

The Ethernet extension cable connects from the mainboard inside of the printer to the outer case of the machine.

Epax screen protectors are similar to a cell phone's anti-scratch screen protector but are tailored to work with Epax Printers. Epax screen protectors are a great way to protect your LCD screen from potential damage that may occur if there is a resin spill.

Please make sure you choose the right screen size for your model.

There are protective films on both sides of the screen protector.  When you apply the protector, you need to peel off the film labeled "back" and then apply using the plastic spatula to the screen's surface carefully, starting from one corner. Having some bubbles may be unavoidable but they should not affect your prints.

This is an optional digital heater addon for the X10-8KW Printer.  

The Heater mounts on the left side of the build arm and will heat the entire print chamber allowing the resin and build plate to be heated to the set temperature.

This add-on requires a stronger power supply. The power supply that the stock X10-8KW comes with will not work. This add-on requires a power supply that is at least 24V 12.5A.

• X10 size fits for all EPAX X10/E10 printers
• X1-4KS size fits for all EPAX X1 series printers.
• Excellent slippery surface: enabling faster printing with less release force and less lifting distance.
• Shipped in protective tube.  
• Each pack contains one (1) film
• 0.3mm thickness 

These films are composite films with a coating on one side to ensure great slippery.  Used in LCD, DLP and SLA machines where fast printing is more important than quality/durable parts.

Note:  The sides are directional.  Do not put it upside down.  See instructions on the film.  There is a protective film on the actual eSLIP film.  The protective film needs to be removed.

Difference between nFEP film and eSLIP/ACF film:

nFEP film is more elastic.  As such, it is less likely to be damaged by residues in vat.  It is recommended for all resin 3D printers, especially jewelry/dental applications where details and quality are more important.  nFEP film has great air permeability, which leads to less vacuum suction force.

eSLIP/ACF film is more rigid and slippery.  As such it needs a smaller lifting distance and prints can run faster.  Printers with eSLIP film can have an overall 40% speed gain due to lower lifting distance needed.  You also need to increase your bottom exposure time and normal exposure time by 20% because the film has 20% less light through rate.  It is recommended for all resin 3D printers where faster printing is more important than outstanding details.  However, if you leave residues in vat, the film is a bit easier to get damaged than nFEP film.  The coating, and the 0.3mm thickness, lead to a bit loss of light accuracy.  Fast printing resins, because they flow like water, are also not able to make strong and tough parts.  Parts tend to be more brittle.  As such, we don't offer fast printing resins.  You can use the film with normal resins and it can still speed up somewhat due to lower lifting distance alone.